All STIHL gasoline-powered engines can be used with up to a 10% (E10) blend of ethanol in the gasoline/engine oil mix. We also recommend that if a unit will be left unused for more than 30 days that it be stored 'dry.' This means emptying the fuel tank and then restarting and letting the unit run until all the fuel is consumed and the engine stops. For maximum performance and engine life expectancy, we also recommend using STIHL HP Ultra 2-cycle engine oil. Note: STIHL recommends use of fuel with no more than 10% ethanol content.
Using fuel with greater than 10% ethanol content may cause damage to your equipment and may void your STIHL warranty. The most common reason is due to too many attempts trying to start the machine in the choke position. When starting a unit, make sure to follow the starting instructions in your. The manual provides the proper instruction for starting procedures, but there are many conditions that may affect how the unit starts. A good rule of thumb to follow is to remember that when placing the switch control to the full choke setting, more liquid fuel and less air flow into the combustion chamber in order to create a higher chance for ignition. Pulling the rope more than two to three times in this setting may flood the engine.
The operator should move the Master Control Lever™ or choke lever from the full choke setting after three to four pulls even if the engine does not fire. Moving the lever to the next setting, the half choke or part throttle position will allow more air into the combustion chamber and help resolve the flooding condition. The way our units lubricate a chain, most of the oil is distributed around the inside of the bar rails as it is circulated by the oil reservoirs in each drive link of the chain. The amount of oil being circulated inside the bar at any given time can be between.3 and.5 oz. As a general rule of physics, the oil will be pulled down by gravity once the chain stops turning, collecting at the bottom of the bar and seeping through the chain to puddle underneath the bar & chain assembly as well as under the drive sprocket. The fact that it appears to be continuing to seep after the unit is cut off for several days is owed to the viscosity of the oil and the anti-flinging compound (lithium) mixed with the oil at the refinery.
These factors give the oil a very thick consistency, which in turn explains a slower flow rate. This condition is deemed to be normal for any chainsaw with a similar bar & chain lubricating system. If the unit continues to seep oil after a few days, the problem may be the vacuum relief valve located in the side of the engine housing between the oil output hole and the bar stud(s).
This valve has an internal spring and ball type arrangement with the ball pressed against the vent hole of the casing of the valve, when the tank develops a vacuum from the normal process of the oil being pumped out. The ball is pulled away from the hole, allowing air to enter into the tank and break the vacuum so that oil can continue to flow to the bar and chain assembly.
Once the vacuum is relieved, the spring pushes the ball back against the hole of the valve casing. Sometimes debris may become trapped between the ball and the hole. This would cause the oil to keep 'weeping' because there must be some measure of vacuum in the tank to keep the oil from flowing freely once the unit is shut down.
More often than not, all one needs to do is to take a small pin or needle and push it into the hole of the valve (identifiable as a small silver disk with a small hole in the center) about 6 or 7 times to loosen the debris. This should re-seal the orifice and keep the oil from seeping from the output hole when the saw is stored. Kickback occurs when the moving saw chain near the upper quadrant of the bar nose contacts a solid object or is pinched. The reaction of the cutting force of the chain causes a rotational force on the chainsaw in the direction opposite to the chain movement. This may fling the bar up and back in an uncontrolled arc mainly in the plane of the bar. Under some cutting circumstances the bar moves towards the operator, who may suffer severe or fatal injury. Kickback may occur when the nose of the guide bar is pinched unexpectedly, unintentionally contacts solid material in the wood or is incorrectly used to begin a plunge or boring cut.
![]()
It may also occur during limbing. The greater the force of the kickback reaction, the more difficult it becomes for the operator to control the saw. Many factors influence the occurrence and force of the kickback reaction. These include chain speed, the speed at which the bar and chain contact the object, the angle of contact, the condition of the chain and other factors. The carburetor comes from the factory with a standard setting.
This setting provides an optimum fuel-air mixture under most operating conditions. With most carburetors, it is only possible to adjust the engine idle speed within fine limits. Quite often adjusting the carburetor will not solve acceleration issues. To find the correct setting for your machine, please refer to your instruction manual.
If you do not have a copy of your instruction manual, please go to our where you can download a PDF version. These protective garments contain pads of cut-retardant material designed to reduce the risk or severity of injury to the body parts covered by the pads in the event of contact with a rotating chain.
The fibers in the pads provide extra layers of material and are designed to rip apart if they come into contact with the moving chain and to clog the sprocket and stop the chain in certain circumstances. In some contacts, the pads may stop the chain. In other contacts, the pads will resist the cutting process only for a fraction of a second. The actual degree of protection afforded will vary with the speed of the chain at the time of contact, the power and torque of the saw, the design of the sprocket and similar factors. Follow the washing instructions.
Improper care may destroy cut-retardant properties of the material. During shipping these pads may become compressed.
By washing them prior to use and weekly during regular use, these pads fluff up and offer maximum protection. Only if you plan to 'mothball' your lawn trimmer, or chainsaw for a longer period - say during the winter months - should you pay a little more attention to the topic of 'care.' This will ensure that your equipment, when required, will be ready for action. To get the equipment ready for winter, clean it first.
The air filter, the cylinder fins, the spark plug and the dismantled cutting tool should be checked and cleaned (also see Instruction Manual). Metal parts should be lightly coated with oil to protect them from rust and corrosion. The spark arresting screen in the muffler should be cleaned or replaced with a new one. The fuel tank should be emptied. Run the engine until the fuel system is dry (Warning! Do not operate the throttle. Run the equipment only at idle speed until the engine stops!) STIHL recommends the use of STIHL MotoMix ® fuel which is pre-mixed with STIHL HP Ultra synthetic oil.
Contains no ethanol and has a storage life of up to two years. STIHL MotoMix ® can be left in the machine during seasonal storage. For winter storage, a dry and, if possible, dust-free and frost-free place would be ideal.
You can save space if you hang the equipment. And remember: standard pump gasoline deteriorates. To avoid problems, only purchase enough fuel that can be used within sixty days unless it is STIHL MotoMix ®. Please refer to the Maintenance Schedule which can be found in the. Note that most brands of new saw chain will not exactly match the shape and fit of a round file radius and is not a defect in the chain.
When STIHL saw chain is manufactured, the cutter teeth are shaped to precise angles with highly specialized machines to provide optimum performance of the new saw chain. After the manufacturing process, a simple round file of specific diameter with the appropriate file guide is recommended to help more easily maintain the cutting performance of your saw chain. While a new saw chain does not exactly match the shape and fit of a round file, a few strokes of the correct file diameter with the appropriate file guide will quickly form the shape of the cutter tooth to match the fit and radius of the file. For instructions on how to sharpen STIHL Saw Chains. Additional information and instructions can also be obtained from your.
Check the spark arrestor screen and see if the screen has carbon deposits on it. If it does then you need to clean the spark arrestor screen and re install it in the muffler. You can clean it by burning off the carbon.
The air filters on the TS 700 Cut Off Saw do not need to be cleaned, they only need to be replaced when the unit starts running poorly. The carburetor could have something in it that is keeping the needle from closing and flooding out the unit. I would suggest taking this unit to a Stihl dealer that has a Gold Certified Technician.
The show is arguably one of the most popular Tamil talk shows in Tamil Nadu.
![]()
You can use the dealer locator on the the Stihl USA website. I have included a link. You can type in your zip code and it will tell you where the closest dealer is and what level of technician they have. May 14, 2010.
![]()
Consumer Product Safety Commission is charged with protecting the public from unreasonable risks of injury or death associated with the use of thousands of types of consumer products under the agency’s jurisdiction. Deaths, injuries, and property damage from consumer product incidents cost the nation more than $1 trillion annually. CPSC is committed to protecting consumers and families from products that pose a fire, electrical, chemical or mechanical hazard.
CPSC's work to help ensure the safety of consumer products - such as toys, cribs, power tools, cigarette lighters and household chemicals -– contributed to a decline in the rate of deaths and injuries associated with consumer products over the past 40 years. Federal law bars any person from selling products subject to a publicly-announced voluntary recall by a manufacturer or a mandatory recall ordered by the Commission.
To report a dangerous product or a product-related injury go online to or call CPSC's Hotline at 800-638-2772 or teletypewriter at 301-595-7054 for the hearing impaired. Consumers can obtain news release and recall information at www.cpsc.gov, on Twitter @ or by subscribing to CPSC's. The link you selected is for a destination outside of the Federal Government. CPSC does not control this external site or its privacy policy and cannot attest to the accuracy of the information it contains. You may wish to review the privacy policy of the external site as its information collection practices may differ from ours. Linking to this external site does not constitute an endorsement of the site or the information it contains by CPSC or any of its employees. Click Ok if you wish to continue to the website; otherwise, click Cancel to return to our site.
The following STIHL products can be retrofitted with STIHL connected: BGA 45, BGA 56, BGA 100, FSA 45, FSA 56, FSA 130, HSA 45, HSA 56, MA 235, MSA 120, MSA 160 T, RMA 339, RMA 443, RMA 448, RMA 2 RT BG 50, BG 56, BR 430, BR 500, BR 600, BR 700, FC 91, FS 38, FS 40, FS 55, FS 56, FS 91, FS 131, FS 311, FS 460, FS 490, FS 510, FS 560, HS 46, HS 56, HS 82, HS 87, MS 170, MS 180, MS 201 T, MS 231, MS 251, MS 261, MS 362, MS 500i, RM 443 (MB 443), RM 448 (MB 448 VC), RM 655 YS (MB 655 YS), RM 756 (MB 756 YC), RT 4082, RT 6127 ZL, TS 420, TS 440, TS 500i. During initial setup, it is essential to check that the battery has been correctly inserted into the STIHL Smart Connector and the isolation film has been removed. The LED signal must light up in green after the battery has been inserted.
Please also ensure that the smartphone system requirements are fulfilled, all permissions have been enabled for the STIHL app, and Bluetooth is switched on. Note: Your smartphone must be within 33 feet (10 meters) of the STIHL Smart Connector in order to detect it.
You may need to wait up to 60 seconds for detection. The adhesive tape and screws, including plain washers, are supplied to suit the STIHL Smart Connector. Only the provided securing materials may be used when using the “sticking” or “screwing” methods to secure the STIHL Smart Connector. The dimensions of supplementary securing options such as “rivets” or “cable ties” mean that these options depend on the respective attachment location, and must therefore be selected and procured as appropriate.
![]()
Where applicable, please note the information in the operating instructions.
. Type: Tracked Skid Steer Loader. Make: New Holland. Engine Type: 4 cylinder diesel. Engine HP: 81.
Indicated Hours: 1356. Previous Registration No: 755930 NSW. Registration Expiry: Sold without registration, no number plates. Fleetwood mac album download zip. Transmission: Hydrostatic. Track Width: 450mm. Undercarriage Condition: Fair. Mere solah singar serial song download.
Features: Auxillary Piping, FOPS, Enclosed A/C Cab. Attachments: Buckets 2120mm (W), Quick Hitch, 4 in 1 bucket. Other: Front Work Lights, Indicators, Amber Beacon, Joystick & Foot Pedal Operated.
Dimensions 4000 x 2120mm, Weight Approx 4216kg. GraysOnline advises all buyers that all plant offered for sale at auction may not be fit for use in a workplace. It is the buyers/owners responsibility to ensure that an operational risk assessment is undertaken, prior to use, and the plant be brought to a condition which complies with relevant State Legislation, Regulations and applicable Codes of Practice. GraysOnline will provide:. Safety information relating to the condition of the item of plant for sale (Plant Hazard Reports). Clear identification and marking to identify that the plant item is only suitable for scrap or spare parts. Site Access, PPE and Removal of Plant requirements are listed under the Inspection and Collection Headings.
Please note:. Persons under the age of 15 years will not be permitted onsite. Tradespeople eg; electricians, plumbers etc will be required to produce the relevant licence before commencing work on site. Riggers, Forklift and Crane Drivers etc will be required to produce the relevant license before commencing work on site.
It is a condition of entry to site that all visitors comply with any directions given by Grays (NSW) Pty Ltd staff or their representatives. Work carried out on this site must be completed in a manner compliant with all Occupational Health & Safety legislation. All power tools and equipment used on this site must be tested (tagged) safe for use in accordance with AS3760 service testing and inspection of electrical equipment. Grays (NSW) Pty Ltd will specify, based on the hazards present on the site, the mandatory personal protective equipment required to be worn prior to approval being given for entry to the site. (eg; safety footwear, safety eyewear, hard hats etc). The use of certified equipment, harnesses, work platforms etc will be required for any work carried out above 1.8metres. Enclosed footwear must be worn onsite – Safety boots may be required at industrial sites.
If you have not purchased electrical tools and equipment in this auction disregard this notice. Electrical Power Tools and Equipment (Inc. Electrical leads) The electrical articles in this auction have not been proved to be electrically safe.
The electrical articles have not been tested by a qualified electrical worker and have not been proved to be electrically safe. General advice on how to use second-hand electrical power tools and equipment (including electrical leads) safely. General safe use advice for electrical power tools and equipment etc.
Intended for use with rated voltage of not more than 250V for single phase appliances and 480V for other appliances. This advice is not intended to replace specific manufacturer's information but can be used as a general guide. This advice does not cater for young children or people who are physically weak.
Stihl Ts400 Serial Number Location
You are urged to:. Use the power tool only for its intended purpose. If the power tool is for indoor use only, do not use outdoors. Do not immerse the power tool in water unless it is designed for this purpose. Keep hands, fingers, feet, toes and hair away from dangerous moving parts, cutting blades and the like. Do not use electrical power tools in the rain.
Make sure you have dry hands when operating an electrical power tool. Do not use a damaged power tool. A power tool may not be intended for use by children or people with an illness or disability without supervision. Young children should not be allowed to play with the power tool. Some power tools require special precautions for installation or user maintenance or both.
The plug must be removed from the socket-outlet before any cleaning or maintenance is done. Do not place cord extension sockets or portable power outlet boards where they may be splashed or where moisture may get in. Ensure ventilation holes or outlets are not blocked or partially obstructed. If a fixed power tool does not have a supply cord and plug or other means for disconnection from the supply, a means for disconnection must be incorporated into the fixed wiring according to the Wiring Rules. If the supply cord or plug is damaged:. The manufacturer or its service agent or a similarly qualified person must replace the cord to prevent an accident. Power tools with specially prepared cords must be replaced by a special cord or assembly available from the manufacturer or its service agent.
Other power tools that have a supply cord that cannot be replaced, should be scrapped. The power tool should be maintained in order to ensure a long, useful life and to protect the operator against electric shock or mechanical mishaps. A safety switch can enhance electrical safety when using electrical power tools.
Motor Dealer Licence: MVD277714 This Sale is Pick Up Only from Various Locations, South Australia. Please refer to the descriptions to determine the location of each asset. These Assets are Used therefore Inspection is Highly Recommended Prior to Bidding. Description, Photos and Condition Reports (if any) Should Be Used as a Guide Only. Bids on assets in this sale should be made based on your own inspection and assessment of the goods. GraysOnline do not test auction items. We provide no warranty as to the items working condition or suitability for its intended purpose.
The assets may have experienced moderate to heavy usage by consumers and have not been tested to ensure that they function according to the manufacturer's specifications. Some individual items may show signs of wear common with used items and in some instances accessories may vary from the standard (for example, software or manuals may be missing or different, no original packaging). (As per the bidders agreement that you have agreed to). PLEASE NOTE: THIS IS AN AUCTION SALE. ALL ASSETS IN THIS SALE ARE SOLD “AS IS” WITHOUT WARRANTY AND COOLING OFF PERIOD. The terms and conditions of the online auctions may change from time to time. Please ensure you clearly read the special terms and conditions contained in this page and also in the bidders agreement.
Continuing to use the online auction service following amendments to these terms & conditions will constitute your acceptance of the new terms & conditions applying to this service. Terms & conditions can be found GraysOnline guarantee that all vehicles/boats/motorbikes in this sale are sold with clear title. Bidders may find when they do perform a PPSR check (highly recommended) in many cases the cars do have an encumbrance, which will be lifted as soon as the vehicle is sold at auction and monies are cleared in our account. Collection of assets is the responsibility of the purchaser. Delivery is not available.
Asset packaging and removal are the purchasers responsibility in the time frame specified for this sale. Goods not collected within this time frame will be deemed abandoned. Invoice totals exceeding $5000 must be paid by direct deposit. Variable Buyer's Premiums apply to all lots purchased in this auction. GraysOnline will not be organising transport of goods. Please consider this prior to bidding. Please take care when making a bid as once your bid is placed, it cannot be withdrawn and will not be cancelled.
If you are unsure do not bid as no refunds will be given. GraysOnline Staff are here for security purposes only. Please make sure you have people to help you load your items and right transport. Items must be inspected before removal from Grays as refunds or exchange are not given under any circumstances. Pick ups are not allowed outside of the dates/times specified. This Sale is GST Exclusive This Sale has a Variable Buyers Premium where the percentage of buyer’s premium will change once a bid price of $1000 or more is reached.
A 20% Buyer’s Premium applies when the bidding is less than $1000, moving to 7.5% or 15% buyer’s premium once the bidding reaches $1000 or more. The Buyer’s Premium will be added to your final bid price. For Example: Successful Bid Price is $100 + 20% Buyers Premium = $120 +10% GST = Invoice Total of $132.00 Successful Bid Price is $1000 + 15% Buyers Premium = $1150 +10% GST = Invoice Total of $1265.00 Successful Bid Price is $1000 + 7.5% Buyers Premium = $1075 +10% GST = Invoice Total of $1182.50 Asset Condition - Please refer to the individual lot description for asset condition. Most lots have pictures assigned to them. These should be taken as a guide only. Payment - Invoice totals exceeding $5000 must be paid by direct deposit within 2 days of auction closing. Contact (02) 9741 9600 or email for an exact invoice total.
For invoices totalling less than $5000, your credit card will be debited within 2 days of auction closing. To assist in the processing of payments please have funds available. Invoice totals exceeding $5000 will not be split. For invoices totalling in excess of $5,000 GraysOnline reserves the right to charge a deposit against the purchaser’s credit card to a maximum of $5,000 or 20% of the invoice total. In bidding in this sale, the buyer agrees without reservation to GraysOnline doing so. Any payment enquiries, please email. As registration and ownership requirements vary from state to state buyers should familiarise themselves with the registration requirements of the state in which the vehicle will be registered.
As is standard auction practice the buyer is responsible for state transfer fees, duties etc. That may apply.
Please note: Please note: If sold unregistered then the number plates will be removed. If sold with registration, the registration can only be transferred in the state where that registration is held, otherwise it will be sold unregistered and the number plates will be removed. Please check the lot description for each vehicle. For SA registration, once your invoice is paid, you’ll need to visit a motor registry with:. Your paid Grays Online Invoice (you will not need the old registration paperwork, these will not be given with the vehicle).
Proof of identity. If you’re registering the vehicle in the name of a company or organisation you will need to also provide proof that it is a legal entity.
Application for Transfer of Registration form You may need to pay for:. General registration charges.
Transfer & Motor Vehicle Duty Fees. Stamp duty. Number plates.
Late transfer surcharge. A surcharge will be applied to customers who fail to transfer the registration within 14 days of the date of acquisition. For further advice and information regarding Registration in SA please refer to Government of SA Service. Typically, auctions end at the closing time posted. There are some exceptions to this, however.
If there are any bids on a particular lot within 10 minutes. of the auction closing time ('Going, Going, Gone!' Period), it will be extended until there are no bids for 10 continuous minutes. There is no limit to the number of times an online auction can be extended. This makes GraysOnline work more like a live auction where the bidding does not stop as long as there is still interest in the product, rather than assigning an arbitrary cut-off time. To ensure that you do not get outbid make sure you monitor the auction until you have won the item or enter a bid that you think will win!
(. refer to Bidders Agreement for full details of 'Going, Going, Gone!' Inspection of the assets is highly recommended.
Bids on assets in this sale should be made based on your inspection and assessment of the goods. Descriptions and photographs should be used as a guide only. If you are unsure do not bid as no refunds will be given. Items in this sale have not been tested and are sold on an 'As Is' basis. Inspection of the assets can be made at the following times:. MONDAY 11th September 2017 from 9:00am to 4:00pm only for assets listed at GraysOnline, Pooraka, SA.
All other locations by appointment only, please call Byron on 0437 689 985. Location:. GraysOnline, 3 Maxwell Road, Pooraka, SA, 5095. All other locations by appointment only. Site Access:. Persons under the age of 16 years will not be permitted on site unless accompanied and supervised on site. It is a condition of entry that all persons entering the site comply with any directions given by GraysOnline staff, their representatives or the site controller.
It is a condition of entry that all persons conduct themselves in a manner which does not endanger the health and safety of other persons on site, and which does not create a risk to health and safety. Personal Protective Equipment (PPE):. GraysOnline will specify, according to the hazards and risks assessed as present on the site, any mandatory PPE required to be worn prior gaining approval to entry to the site. This equipment may include Safety Footwear, Safety Eyewear, Hearing Protection, and Head Protection, or any other item of PPE deemed necessary. DELIVERY IS NOT AN OPTION FOR THIS SALE. THE REMOVAL OF THE ASSETS IS THE BUYER'S RESPONSIBILITY. ASSETS ARE LOCATED IN VARIOUS LOCATIONS IN SOUTH AUSTRALIA & HAVE NOT BEEN TESTED BY GRAYSONLINE.
ASSETS THAT HAVE BEEN PREVIOUSLY REGISTERED WILL BE SOLD WITH NO REGISTRATION OR PLATES. PLEASE NOTE THAT ALL B-TYPE ASSETS REQUIRE SPECIFIC VEHICLES FOR REMOVAL, TO BE ORGANISED BY BUYER'S AT BUYER'S EXPENSE.
Pick ups are not allowed outside of the dates/times listed below. Pick up can only be made once cleared funds are received. Purchasers cannot pick up until full invoice is paid. Goods will only be released with correct buyer details being provided (Full Buyer Name, Sale and Lot Number and ID). Pick-Up Date/Time:. Assets must be collected on MONDAY 18th September 2017 from 9am - 4pm for assets located at GraysOnline, Pooraka, SA. All other locations by appointment - once you have paid, you will receive an email with contact details to arrange the collection.
Location:. GraysOnline, 3 Maxwell Road, Pooraka, SA, 5095 and Various Other Locations in South Australia (refer lot description). Third Party Pick Up: If you intend to send a third party to collect your goods on your behalf, you need to send them with a copy of your Winners E-mail and Paid Invoice, a photocopy of your photo ID and signed note of authority permitting GraysOnline staff to release your purchases to the third party. Please Note:. Children under the age of 16 will not be permitted on site.
It is a condition of entry that all persons entering the site comply with any directions given by GraysOnline staff, their representatives or the site controller. It is a condition of entry that all persons conduct themselves in a manner which does not endanger the health and safety of other persons on site, and which does not create a risk to health and safety.
All persons visiting site must be wearing fully enclosed shoes, preferably safety boots. Packaging and collection of assets is the responsibility of the purchaser. Delivery is not available for this auction.
Any items not collected after the nominated collection times may be deemed abandoned. Items must be inspected before removal from site as refunds or exchange are not given under any circumstances.
Personal Protective Equipment (PPE):. GraysOnline will specify, according to the hazards and risks assessed as present on the site, any mandatory PPE required to be worn prior gaining approval to entry to the site.
This equipment may include Safety Footwear, Safety Eyewear, Hearing Protection, and Head Protection, or any other item of PPE deemed necessary. GraysOnline will specify the site requirements for the safe removal of plant from the site. All work carried out on site will be performed in a manner compliant with the relevant State Occupational Health and Safety Legislation. All work undertaken on the site must be performed by suitably qualified and insured persons. Licensing of Tradespersons - All tradespersons must possess the relevant licences to undertake plant disconnection and removal of plant activities. Copies of these licenses will be requested prior to the commencement of work and copies/license details will be retained by GraysOnline.
Insurances - Copies of Insurances - PI/PL and Workers Compensation will be required to perform work on the site and copies will be retained by GraysOnline. Agreement - before any wok commences the contractor/tradesperson must sign and agree to adhere to GraysOnlines OHS work practices. Safe Work Method Statement (SWMS) - the contractor/tradesperson will be required to submit a completed SWMS. Work at Heights - All work above 2.0 metres will require the use of certified equipment. This equipment may include safety harnesses and work platforms. All equipment used will be in within the safe test date requirement for such equipment.
Serial Number Location On Stihl Ts420
All work at heights risks will controlled. Electrical Equipment- All equipment brought onto site must be considered safe and fit for use and be tested and tagged as required by AS/NZS 3760:2003: In-service safety inspection and testing of electrical equipment.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |